WSAL19543 – SIM7600G-H-PCIE/en

Documentation notice: This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

Summary

Technical data sheet and setup guide for the SIM7600G-H-PCIE (Waveshare/SIMCom): frequency bands, interfaces, power supply, indicators, Raspberry Pi setup via Minicom, and selected AT commands.

Related products at JW Tech

WSAL19543 – SIM7600G-H-PCIE SIMCom Original 4G LTE Cat-4 Module, Global Coverage, GNSS, Mini-PCIe Connector

Technical overview

M.2 B Key form factor; dimensions 42.0 × 31.4 × 3.8 mm; operating temperature −40 °C to +85 °C.
Power supply 3 V to 4.2 V; approximately 4.0 V recommended for proper operation.
LTE-FDD bands: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66.
LTE-TDD bands: B34, B38, B39, B40, B41; WCDMA: B1, B2, B4, B5, B6, B8, B19; GSM: 850/900/1800/1900 MHz.
GNSS: GPS, Beidou, GLONASS, GALILEO, QZSS; antenna connectors IPEX-4 (LTE main, LTE diversity, and GNSS antenna).
Data rates: LTE 150 Mbps downlink / 50 Mbps uplink; HSPA+ 42/5.76 Mbps; WCDMA 384 Kbps; EDGE 236.8 Kbps; GPRS 85.6 Kbps.
Interfaces: UART, USB, GPIO; supported OSes Windows/Linux/Android; protocols TCP/IP/IPv4/IPv6/Multi-PDP/FTP/FTPS/HTTP/HTTPS/DNS; SMS MT/MO/CB/Text/PDU; firmware update via USB/FOTA.
STA/NET LED states: both off = powered off; both on = operating; STA on, NET blinking = no SIM or weak signal; NET blinking/on during shutdown = shutting down.
Raspberry Pi setup: install minicom, open /dev/ttyUSB2, run AT+CUSBPIDSWITCH=9011,1,1, then sudo dhclient -v usb0 for RNDIS data access.
AT commands cover test, echo, manufacturer/type/SN/firmware version checks, signal quality (AT+CSQ), SIM status (AT+CPIN?), network status (AT+CREG?, AT+COPS?), and network mode selection (AT+CNMP).

Commands and examples – verify before use:

AT
ATE0
ATE1
AT+CGMI
AT+CGMM
AT+CGSN
AT+CSUB
AT+CGMR
AT+IPREX
AT+CRESET
AT+CSQ
AT+CPIN?
AT+COPS?
AT+CREG?
AT+CPSI?
AT+CNMP
AT+CUSBPIDSWITCH=9011,1,1
AT+CNBP=0x0002000000400183,0x000001E000000000,0x0000000000000021
AT+CNBP=0x0002000000400180,0x480000000000000000000000000000000000000000000042000001E200000095,0x0000000000000021

Notes and version constraints

M.2 B Key is not compatible with MINI-PCIe connectors – verify the interface before use.
Do not plug in the module while it is powered.
If the module does not connect normally after successful setup: try one of the two AT+CNBP commands to change the frequency.
The exact return values of AT+CSQ, AT+COPS? and AT+CREG? are given only as placeholders in the source; actual values must be read from the device.
Version-sensitive steps and driver installation may vary by OS version; human confirmation required when uncertain.

Source and revision record

SIM7600G-H-PCIE - Waveshare Wiki
Source revision: 77702
Captured: 2026-09-01T04:29:19+00:00
SHA-256: 82af5db3010693d98c52657dc409d723b930f7aca1dd9861cd60a3d7e6385a25