Quelltext der Seite WSAL17372 – SIM7600G-H 4G HAT/en

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The SIM7600G-H is a 4G module HAT for Raspberry Pi and Jetson Nano. It supports LTE Cat-4 (up to 150 Mbps downlink, 50 Mbps uplink), 3G/2G fallback, and GNSS positioning (GPS, BeiDou, Glonass). The board provides a SIM card slot (1.8 V / 3 V), a USB-to-UART converter (CP2102), an audio jack for calls, a TF card slot, and two status LEDs. Operating voltage can be set to 3.3 V or 5 V via jumper.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL17372 WSAL17372 – SIM7600G-H 4G HAT For Raspberry Pi, LTE Cat-4 4G / 3G / 2G Support, GNSS Positioning, Global Band]

== Technical overview ==
* Interfaces: 40-pin GPIO expansion header, UART breakout pins, USB interface, audio output, TF card slot
* Supported frequency bands: LTE-TDD B38/B39/B40/B41; LTE-FDD B1/B3/B5/B7/B8/B12; 3G UMTS/HSPA+ B1/B5/B8; 2G GSM/GPRS/EDGE 850/900/1800/1900 MHz
* GNSS reception: GPS, BeiDou, Glonass (no GALILEO/QZSS per spec table)
* Default baud rate: 115200 bps; autobauding range 9600–115200 bps
* New version changes (2H 2021): added 330 µF electrolytic capacitor, PWR/Flightmode jumpers, solderable pads for VCCIO and USB, changed power IC to SPX29302, silkscreen renamed from WPI to BCM naming
* Power on/off: PWR and 3V3 shorted by default → auto power-on when connected to supply; manual control via PWRKEY button or Raspberry Pi D6 pin possible
* Flight mode: not enabled by default; controllable via jumper between Flight and D4
* Application areas: medical devices, smart payments, public network intercom, environmental monitoring, fleet management, smart industry, smart agriculture

'''Commands and examples – verify before use:''' 
<syntaxhighlight lang="text">
AT+CGPSNMEAPORTCFG=3
AT+CGPSNMEA=197119
AT+CGPSINFOCFG=10,31
AT+CGPSAUTO=1
AT+CRESET
</syntaxhighlight>

== Notes and version constraints ==
* The source does not provide a complete AT command list; only the commands listed above are explicitly mentioned.
* No information on price, stock, certifications, or warranty is present in the source – such values must not be invented.
* Compatibility with boards other than Raspberry Pi 4B and Jetson Nano is not confirmed in the source.
* The new version (from 2H 2021) introduces hardware changes; older stock may have different pin layouts.
* MMS is explicitly stated as unsupported in the FAQ.
* The reset pin was intentionally not brought out because it can only reset a limited set of functions.

== Source and revision record ==
* [https://www.waveshare.com/wiki/SIM7600G-H_4G_HAT SIM7600E-H 4G HAT - Waveshare Wiki]
* Source revision: 103975
* Captured: 2026-08-31T04:17:35+00:00
* SHA-256: <code>fa878b32f1fdcbcac458c7d08f59c189ab865d7f80bcad08e91ed99bca876fe1</code>