Quelltext der Seite WSAL15873 – 10.3inch e-Paper HAT (D)/en

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The 10.3inch flexible E-Ink display HAT (D), resolution 1872 × 1404, is driven by the IT8951 controller via USB, SPI or I80 and supports partial refresh. It is designed for Raspberry Pi and other host boards.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL15873 WSAL15873 – 1872×1404, 10.3inch flexible E-Ink raw display]
* [https://shop.jw-tech.eu/p/WSAL16712 WSAL16712 – 1872×1404, 10.3inch flexible E-Ink display HAT for Raspberry Pi]

== Technical overview ==
* Resolution 1872 × 1404; active area approx. 209.664 mm × 157.248 mm
* Controller: IT8951; interfaces: USB/SPI/I80
* Operating voltage: 5 V
* Full refresh time: approx. 450 ms (measured value)
* Refresh power: typ. 1.2 W; standby: typ. 0.1 W
* Viewing angle: &gt;170°
* Colors: black/white; gray levels: 2–16 (1–4 bit)
* Housing dimensions: 227.7 mm × 165.8 mm × 0.647 mm
* Operating range: 0 to 50 °C; storage: −25 to 70 °C
* Raspberry Pi connection uses GPIO pins 5V, GND, MISO(P9), MOSI(P10), SCK(P11), CS(P8), RST(P17), HRDY(P24).

'''Commands and examples – verify before use:''' 
<syntaxhighlight lang="text">
wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.60.tar.gz
tar zxvf bcm2835-1.60.tar.gz
cd bcm2835-1.60
./configure
make
sudo make check
sudo make install
wget https://github.com/joan2937/lg/archive/master.zip
unzip master.zip
cd lg-master
make
sudo make install
sudo apt-get update
sudo apt install gpiod libgpiod-dev
sudo raspi-config
sudo nano /boot/config.txt
sudo reboot
sudo apt-get install p7zip-full
sudo wget https://files.waveshare.com/upload/8/80/IT8951_20200319_Release.7z
7z x IT8951_20200319_Release.7z -O./IT8951
</syntaxhighlight>

== Notes and version constraints ==
* The source contains no explicit warnings; the following points require human confirmation:
* The FPC and glass panel of the large screen are fragile – handle with care when developing; reinforce the FPC with tape if needed.
* Connect all cables before powering on; hot-plugging is not supported.
* In low-temperature environments, color deviation may occur; recommended to stabilize at 25 °C for 6 hours.
* Screens without a backlight continue displaying the last content after power failure; avoid direct sunlight.
* Recommended update interval: at least every 24 hours to prevent burn-in.
* Prolonged high-voltage operation can burn out the screen; switch to sleep mode or power off after each refresh.
* After deep sleep mode, the screen must be re-initialized via software.

== Source and revision record ==
* [https://www.waveshare.com/wiki/10.3inch_e-Paper_HAT_(D) 10.3inch e-Paper HAT (D) - Waveshare Wiki]
* Source revision: 100988
* Captured: 2026-08-31T03:09:00+00:00
* SHA-256: <code>02123632609a8ea30e17b6eb5afa2e171d699621fb17403a87f443c111a05b22</code>