https://wiki.jw-tech.eu/index.php?action=history&feed=atom&title=WSAL23414_%E2%80%93_RGB-5050-5V-IP65-60D-1M%2FenWSAL23414 – RGB-5050-5V-IP65-60D-1M/en - Versionsgeschichte2026-10-23T21:38:53ZVersionsgeschichte dieser Seite in JW Tech WikiMediaWiki 1.43.9https://wiki.jw-tech.eu/index.php?title=WSAL23414_%E2%80%93_RGB-5050-5V-IP65-60D-1M/en&diff=2352&oldid=prevJWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex2026-09-06T06:02:56Z<p>Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex</p>
<p><b>Neue Seite</b></p><div>__NOINDEX__<br />
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.<br />
<br />
== Summary ==<br />
The RGB-5050-5V-IP65-60D-1M is a 1 m water-resistant (IP65) RGB LED strip using WS2812B chips. It runs at 5 V, contains 60 LEDs per meter and uses a single-wire channel with return-to-zero coding.<br />
<br />
== Related products at JW Tech ==<br />
* [https://shop.jw-tech.eu/p/WSAL23414 WSAL23414 – WS2812 Digital RGB LED Strip, High brightness, Energy-saving And Low power consumption, Cuttable and Programmable]<br />
<br />
== Technical overview ==<br />
* Light source: 5050 LEDs, 60 per meter, 120° beam angle<br />
* Controller chip: WS2812B, 24-bit data word per LED (R, G, B each 8 bits)<br />
* Supply voltage: 5 V; maximum current draw approx. 3.6 A/m at full brightness<br />
* Ingress protection: IP65 (splash-proof), operating temperature range -25 to 80 °C<br />
* Connector: 3-pin PH2.0 header – red = VCC, green = DATA (input/output), white = GND<br />
* Protocol: single-wire bus, return-to-zero code; after receiving 24 bits the DO output forwards data to the next chain element<br />
* Timing values: T0H ≈ 0.35 µs, T1H ≈ 1.36 µs, T0L ≈ 1.36 µs, T1L ≈ 0.35 µs, RESET ≥ 50 µs<br />
* Sample demos available for Raspberry Pi (default pin D18) and Pico (default pin GPIO7)<br />
<br />
== Notes and version constraints ==<br />
* The source lists no concrete command strings or API calls; therefore the commands field remains empty.<br />
* When cascading multiple strips, the source recommends adding a power feed every 300 lights – exact design depends on total length.<br />
* The stated timing tolerances (±150 ns) are tight; MCU implementations must reliably meet this accuracy.<br />
* The source references external demo examples (Pico/Raspberry Pi); whether these still work requires manual confirmation.<br />
* No information on certifications, warranty or price in the source – such details were intentionally omitted.<br />
<br />
== Source and revision record ==<br />
* [https://www.waveshare.com/wiki/RGB-5050-5V-IP65-60D-1M RGB-5050-5V-IP65-60D-1M - Waveshare Wiki]<br />
* Source revision: 74777<br />
* Captured: 2026-09-04T02:55:54+00:00<br />
* SHA-256: <code>48790edca228aaab0c0c7f2387dcd2c7965da761b992911b8e011436edd8c679</code></div>JWTechPublisher