JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

2026-09-05T23:11:23Z

Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

Neue Seite

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The 2.66-inch e-paper module for Raspberry Pi Pico provides a 296×152 pixel resolution in black/white via an SPI interface. It is suitable for low-power displays with long-term display without backlighting.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL20052 WSAL20052 – 2.66inch E-Paper E-Ink Display Module for Raspberry Pi Pico, 296×152, Black / White, SPI]

== Technical overview ==
* Size: 2.66 inch; active area: 60.088 mm × 30.704 mm; panel outline: 71.820 mm × 36.304 mm × 1.05 mm; driver board: 74.0 mm × 37.5 mm
* Operating voltage: 3.3 V; communication: SPI (SPI0, CPHL=0, CPOL=0)
* Resolution: 296 × 152 pixels; pixel pitch: 0.202 × 0.203 mm; grayscale levels: 2 (black = bit 0, white = bit 1)
* Refresh times (measured): partial refresh ~0.3 s; full refresh ~6 s; refresh power typ. 42.4 mW; sleep current < 0.01 µA
* Pico/Pico 2 pin mapping: VCC→VSYS, GND→GND, DIN→GP11 (MOSI), CLK→GP10 (SCK), CS→GP9 (active low), DC→GP8 (high = data, low = command), RST→GP12 (active low), BUSY→GP13
* Command/data control via the DC pin: DC=0 writes a command, DC=1 writes data; CS is held low to enable the module
* Pixel encoding: 1 byte = 8 pixels in MSB format; a monochrome image is transmitted as a bitstream
* Demo code is fetched via wget or git from the Waveshare repository; the C project is built with CMake and Make, producing a .uf2 file flashed onto the Pico via BOOTSEL + USB
* For MicroPython: the appropriate firmware (.uf2) is also loaded via BOOTSEL; Thonny IDE is used to run scripts directly on the Pico
* The display reflects ambient light and requires no backlight; after power-off the last image remains visible

'''Commands and examples – verify before use:'''
<syntaxhighlight lang="text">
cd ~ && sudo wget https://files.waveshare.com/upload/5/5a/Pico_ePaper_Code.zip && unzip Pico_ePaper_Code.zip -d Pico_ePaper_Code && cd ~/Pico_ePaper_Code
git clone https://github.com/waveshare/Pico_ePaper_Code.git && cd ~/Pico_ePaper_Code
mkdir build && cd build && export PICO_SDK_PATH=../../pico-sdk && cmake -DPICO_BOARD=pico -DPICO_PLATFORM=rp2040 .. && make -j9
cp epd.uf2 /media/pi/RPI-RP2/
void EPD_2IN66_Init(UBYTE Mode); // Mode=0 full update, Mode=1 partial update
void EPD_2IN66_Clear(void);
void EPD_2IN66_Display(UBYTE *Image);
</syntaxhighlight>

== Notes and version constraints ==
* Refresh time and power figures are test measurements; real-world values may vary by environment.
* Full refresh causes visible flicker – noted as a normal phenomenon in the source.
* After deep-sleep the e-paper must be re-initialized before it can be refreshed again.
* When waking from sleep, clear the display first to minimize afterimages.
* If the program hangs on “busy”: check wiring and verify SPI clock rate and mode are configured correctly.
* The exact line to uncomment in main.c depends on the precise model; for this module the corresponding 2.66-inch definition must be enabled.

== Source and revision record ==
* [https://www.waveshare.com/wiki/Pico-ePaper-2.66 Pico e-Paper 2.66 - Waveshare Wiki]
* Source revision: 90410
* Captured: 2026-09-02T03:11:15+00:00
* SHA-256: <code>a8f3c6b1ddab9b77aadc4080b22224030b04a97f71cacb94f1cbaa7b79aa6d41</code>

WSAL20052 – Pico-ePaper-2.66/en - Versionsgeschichte

JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex