JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

2026-09-05T22:26:09Z

Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

Neue Seite

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The Waveshare 6inch HD e-Paper HAT uses the IT8951 controller, resolves at 1448×1072 and is driven via USB, SPI, I80 or I2C. It is suitable for Raspberry Pi (HAT), Windows PC (USB) and STM32 (SPI/I80).

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL17490 WSAL17490 – 1448×1072 high definition, 6inch E-Ink raw display]
* [https://shop.jw-tech.eu/p/WSAL17590 WSAL17590 – 1448×1072 high definition, 6inch E-Ink display HAT for Raspberry Pi]

== Technical overview ==
* Resolution: 1448 × 1072 pixels; display size approx. 122.356 mm × 90.584 mm; dot pitch 0.0845 mm.
* Operating voltage 5 V; refresh power typ. 0.6 W; standby power typ. 0.3 W.
* Graphics modes: 2–16 gray levels (1–4 bit); colors are black/white only.
* Full refresh takes under 1 s; a flickering effect during global refresh is normal.
* Viewing angle > 170°; operating temperature 0–50 °C; storage temperature −25–70 °C.
* Interfaces: USB/SPI/I80/I2C; HAT fits the Raspberry Pi 40-pin GPIO header.
* The raw panel requires a separate IT8951 driver board; the HAT already includes it.
* At low temperatures color cast may appear; acclimatize for 6 hours at 25 °C before refreshing.
* FPC and glass panel are fragile; reinforcing the FPC with tape is recommended during development.
* Connect all cables before powering on – hot-plugging is not supported.

'''Commands and examples – verify before use:'''
<syntaxhighlight lang="text">
wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.60.tar.gz
tar zxvf bcm2835-1.60.tar.gz
cd bcm2835-1.60 && ./configure && make && sudo make check && sudo make install
sudo raspi-config
sudo nano /boot/config.txt
sudo reboot
sudo apt-get install p7zip-full
sudo wget https://files.waveshare.com/upload/8/80/IT8951_20200319_Release.7z
7z x IT8951_20200319_Release.7z -O./IT8951
cd IT8951/ && sudo make clean && sudo make -j4
git clone https://github.com/waveshare/IT8951-ePaper.git
cd IT8951-ePaper/Raspberry && sudo make clean && sudo make -j4
make -j4 LIB=LGPIO
make -j4 LIB=GPIOD
sudo ./epd -1.50 0
</syntaxhighlight>

== Notes and version constraints ==
* The stated refresh time < 1 s is an experimental value; actual timing may vary.
* Power figures (0.6 W / 0.3 W) are measured values and can differ depending on driver board and usage.
* The source contains placeholders such as {{{name3}}} through {{{name6}}}; these values are missing from the supplied text and must be confirmed by the supplier.
* Demo commands reference the 19 March 2020 release; newer firmware/driver versions may require different parameters.
* The VCOM value must be read directly from the FPC and passed as a parameter – the exact value is not given here.
* Outdoor use requires UV protection and avoidance of direct sunlight, because charged particles dry out and refresh may fail permanently (irreversible).
* Refresh the screen at least every 24 h to avoid burn-in of a static image.
* After deep-sleep mode, the display must be re-initialized in software before it can be refreshed again.

== Source and revision record ==
* [https://www.waveshare.com/wiki/6inch_HD_e-Paper_HAT 6inch HD e-Paper HAT - Waveshare Wiki]
* Source revision: 110122
* Captured: 2026-08-31T04:20:06+00:00
* SHA-256: <code>016225a7abca26007510d980f857dfa8fbfa2fa41ef3912ecfc27c8e453c093c</code>

WSAL17490 – 6inch HD e-Paper HAT/en - Versionsgeschichte

JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex