JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

2026-09-05T22:14:03Z

Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

Neue Seite

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The Waveshare Compute Module 4 PoE Board is an IO breakout board for developing with or integrating the Raspberry Pi Compute Module 4 (all CM4 variants). It provides PoE power over Gigabit Ethernet, four USB 3.2 Gen1 ports, dual HDMI, two MIPI CSI camera connectors, two MIPI DSI display connectors, a CR2032 RTC battery holder, a PWM fan header with 5 V/12 V selection, and a 40-pin GPIO header for HATs.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL16664 WSAL16664 – Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4S / CM3 / CM3L / CM3+ / CM3+L]
* [https://shop.jw-tech.eu/p/WSAL18606 WSAL18606 – Raspberry Pi Compute Module 4 IO Board With PoE Feature, for all Variants of CM4]
* [https://shop.jw-tech.eu/p/WSAL19883 WSAL19883 – PoE Mini-Computer Based on Raspberry Pi Compute Module 4 (NOT Included), Metal Case, With Cooling Fan]
* [https://shop.jw-tech.eu/p/WSAL20016 WSAL20016 – PoE Mini-Computer Based on Raspberry Pi Compute Module 4 (NOT Included), Metal Case, With Cooling Fan]
* [https://shop.jw-tech.eu/p/WSAL28048 WSAL28048 – Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4S / CM3 / CM3L / CM3+ / CM3+L]
* [https://shop.jw-tech.eu/p/WSAL28049 WSAL28049 – Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4S / CM3 / CM3L / CM3+ / CM3+L]
* [https://shop.jw-tech.eu/p/WSAL28053 WSAL28053 – Compute Module IO Board with PoE Feature, Composite Breakout Board for Developing with Raspberry Pi CM4S / CM3 / CM3L / CM3+ / CM3+L]

== Technical overview ==
* Compatible with all variants of the Raspberry Pi Compute Module 4 (CM4/CM4L).
* PoE: Gigabit Ethernet RJ45 supporting the 802.3af standard; the connected switch must support PoE.
* DC input: wide voltage range of 7–36 V DC; a supply of at least 24 W is recommended.
* Four USB 3.2 Gen1 ports are onboard by default.
* Dual HDMI ports enable dual 4K@30fps output; only one can be active simultaneously by default.
* Two MIPI CSI connectors for cameras; single cameras work only on the CAM0 port.
* Two MIPI DSI connectors for displays; default resolution 800×480 on newer systems (Bookworm).
* RTC chip PCF85063A sits on I2C-10 at address 0x51; requires a CR2032 battery in the holder.
* Fan driver EMC2301 also on I2C-10 at address 0x2f; supports PWM fans.
* Jumpers select between 5 V and 12 V for the fan; default is 5 V.
* 40-pin GPIO header for connecting Raspberry Pi HATs.
* The two DISP connectors cannot be used together by default.
* Micro USB serves as a USB slave port for writing to eMMC, not as OTG.
* No hot-plugging allowed except for USB and HDMI.
* For PoE operation, set the jumper to EN.
* When using RTC, DSI and CSI must remain disabled.
* Kernel version ≥ 6.1.31 is required for the fan driver (check with uname -a).

'''Commands and examples – verify before use:'''
<syntaxhighlight lang="text">
sudo nano /boot/config.txt
dtparam=i2c_vc=on
dtoverlay=i2c-rtc,pcf85063a,i2c_csi_dsi
#dtparam=audio=on
sudo reboot
sudo hwclock -w
sudo hwclock -s
sudo hwclock --set --date="9/8/2021 16:45:05"
sudo hwclock -r
sudo hwclock --verbose
uname -a
dtoverlay=i2c-fan,emc2301,i2c_csi_dsi,midtemp=45000,maxtemp=65000
i2cdetect -y 10
libcamera-hello --list-cameras
libcamera-hello -t 0
libcamera-jpeg -o test.jpg
libcamera-vid -t 10000 -o test.h264
sudo raspivid -t 0 -cs 0
sudo raspivid -t 0 -cs 1
</syntaxhighlight>

== Notes and version constraints ==
* Hot-plugging devices (other than USB/HDMI) may damage hardware.
* The fan must be connected before powering on; connecting it afterwards may damage the driver chip.
* Verify the fan's rated voltage matches the selected jumper setting before connecting.
* PoE operation requires a compatible switch (802.3af); without one, power delivery will not work.
* Exact compatibility of specific cameras or displays depends on the exact model and is not specified here.
* Changes to config.txt require a reboot to take effect.
* If RTC misbehaves, check that the battery is properly seated and charged.
* Kernel versions below 6.1.31 do not support the EMC2301 fan driver.
* Using DSI disables HDMI output by default, even when no DSI display is connected.

== Source and revision record ==
* [https://www.waveshare.com/wiki/Compute_Module_4_PoE_Board Compute Module 4 PoE Board - Waveshare Wiki]
* Source revision: 104450
* Captured: 2026-08-31T03:46:04+00:00
* SHA-256: <code>2a86054d5170579102475f84aac463960f8f66cc72e462ee9e463108a4a6eb68</code>

WSAL16664 – Compute Module 4 PoE Board/en - Versionsgeschichte

JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex