https://wiki.jw-tech.eu/index.php?action=history&feed=atom&title=WSAL16446_%E2%80%93_2.8inch_Resistive_Touch_LCD%2FenWSAL16446 – 2.8inch Resistive Touch LCD/en - Versionsgeschichte2026-10-23T21:20:22ZVersionsgeschichte dieser Seite in JW Tech WikiMediaWiki 1.43.9https://wiki.jw-tech.eu/index.php?title=WSAL16446_%E2%80%93_2.8inch_Resistive_Touch_LCD/en&diff=1682&oldid=prevJWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex2026-09-05T22:34:43Z<p>Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex</p>
<p><b>Neue Seite</b></p><div>__NOINDEX__<br />
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.<br />
<br />
== Summary ==<br />
The 2.8-inch IPS LCD with a resistive touch panel provides 320 × 240 pixels and communicates via a 4-wire SPI bus. The display driver defaults to ST7789; HX8347D is the alternative. The XPT2046 touch controller supports 12-bit ADC at 125 kHz sampling and also provides temperature and battery-voltage measurements.<br />
<br />
== Related products at JW Tech ==<br />
* [https://shop.jw-tech.eu/p/WSAL16446 WSAL16446 – 2.8inch Resistive Touch LCD, 320×240]<br />
<br />
== Technical overview ==<br />
* Display resolution: 320 × 240 pixels, IPS panel, 65K colors (RGB).<br />
* Interface: 4-wire SPI with CPHA=0, CPOL=0; data transmitted MSB-first.<br />
* Default driver ST7789; switch to HX8347D by editing the defines on lines 80/81 of LCD_Driver.h if the display does not render.<br />
* Touch controller XPT2046: 12-bit ADC at 125 kHz, I/O range 1.5–5.25 V, on-chip temperature sensor, battery monitoring 0–5 V.<br />
* Dimensions: overall 79.9 mm × 50.8 mm, active display area 57.6 mm × 43.2 mm.<br />
* Power: 5 V for the panel, 3.3 V logic level; LED backlight with programmable control via LCD_BL.<br />
* Pins: 5V, GND, MISO, MOSI, SCLK, LCD_CS, LCD_DC, LCD_RST, LCD_BL, TP_CS, TP_IRQ.<br />
* Compatible with OpenX05R-C, OpenM128, Open103C, and PIC-based boards (Open16F877A / Open18F4520); pin mappings differ per board.<br />
* Touch calibration is performed with a stylus after launching the demo; drawing becomes possible afterwards.<br />
<br />
'''Commands and examples – verify before use:''' <br />
<syntaxhighlight lang="text"><br />
#define ST7789_DEVICE // Zeile 80 in LCD_Driver.h (standardmäßig aktiv)<br />
//#define HX8347_DEVICE // Zeile 81 in LCD_Driver.h (kommentiert aus, aktivieren zum Umschalten)<br />
</syntaxhighlight><br />
<br />
== Notes and version constraints ==<br />
* Driver switching requires editing LCD_Driver.h; exact line numbers may vary by firmware version.<br />
* Demo projects are tied to specific development boards; verify correct pin mapping before flashing.<br />
* Calibration is version-sensitive: if calibration fails, the driver or firmware may need updating.<br />
* No warranty, certification, or safety-compliance information is present in the source; these must be verified separately.<br />
<br />
== Source and revision record ==<br />
* [https://www.waveshare.com/wiki/2.8inch_Resistive_Touch_LCD 2.8inch Resistive Touch LCD - Waveshare Wiki]<br />
* Source revision: 76384<br />
* Captured: 2026-08-31T03:30:33+00:00<br />
* SHA-256: <code>1b1bcbe31906306a572f0f377135671c4e1f9cacbbe74d32d27df85dd56f1542</code></div>JWTechPublisher