JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

2026-09-05T22:39:27Z

Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

Neue Seite

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
The SIM7020E NB-IoT HAT is a Raspberry Pi module based on the SIM7020E chipset. It enables NB-IoT data communication via serial AT commands and supports protocols such as MQTT, HTTP(S), TCP/UDP, and LWM2M/CoAP.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL15936 WSAL15936 – NB-IoT HAT for Raspberry Pi, for Europe, Asia, Africa, Australia]

== Technical overview ==
* Compatible with Raspberry Pi 2B, 3B, Zero and Zero W via the 40-pin GPIO connector.
* Supported bands: FDD-LTE B1/B3/B5/B8/B20/B28.
* Data rates: uplink up to 62.5 kbit/s, downlink up to 26.15 kbit/s.
* Powered by 5 V; logic level defaults to 3.3 V and can be switched to 5 V via jumper.
* Two status LEDs indicate network registration and data transmission.
* Serial interface with configurable baud rate from 300 to 921600 bps (default 115200 bps).
* Controlled through AT commands following V.25TER, 3GPP TS 27.007, and SIMCOM AT commands.
* The USB port is for power supply or debugging only, not for sending AT commands.

'''Commands and examples – verify before use:'''
<syntaxhighlight lang="text">
AT
ATE1
ATE0
AT+CSQ
AT+CGMR
AT+CGREG?
AT+CGACT?
AT+COPS?
AT+CFUN=0
AT+CFUN=1
AT*MCGDEFCONT="IP","3GNET"
AT+CSOC=1,1,1
AT+CSOCON=0,2317,"118.190.93.84"
AT+CSOSEND=0,0,"Hello World"
AT+CSOCL=0
AT+CSOC=1,2,1
AT+CSOCON=4,524,"116.247.119.165"
AT+CSOSEND=4,0,"Waveshare"
AT+CIPPING="61.135.169.121"
AT+CDNSGIP="www.baidu.com"
</syntaxhighlight>

== Notes and version constraints ==
* The supported frequency bands must match the SIM card provider; otherwise network registration will fail.
* The USB port cannot be used for AT command control – it is limited to power supply or debugging.
* HTTP and MQTT responses may be delayed due to low NB-IoT data rates.
* When using with Raspberry Pi, the hardware serial port must be enabled and the serial login shell disabled.
* Compiling the BCM2835 library may produce Makefile errors; fix by running autoreconf -vfi, then recompile and install.
* Sleep mode is entered by holding PWRKEY for 3–5 s or sending AT+CPOWD=1; wake by pulling the DTR pin high for 3–5 seconds.
* Only NB-IoT-capable SIM cards are suitable; standard SIM cards may not work.

== Source and revision record ==
* [https://www.waveshare.com/wiki/SIM7020E_NB-IoT_HAT SIM7020E NB-IoT HAT - Waveshare Wiki]
* Source revision: 80747
* Captured: 2026-08-31T03:13:43+00:00
* SHA-256: <code>9048acc747d3fa08d77df3ddf9289923fef887c2287c8a0f13026155bf023cd6</code>

WSAL15936 – SIM7020E NB-IoT HAT/en - Versionsgeschichte

JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex