JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

2026-09-05T22:39:22Z

Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex

Neue Seite

__NOINDEX__
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.

== Summary ==
A concise technical introduction to the Waveshare module WSAL10514: specifications, pinout, Raspberry Pi/STM32/Arduino integration and available driver libraries.

== Related products at JW Tech ==
* [https://shop.jw-tech.eu/p/WSAL10514 WSAL10514 – 0.95inch RGB OLED (B)]

== Technical overview ==
* The module is a 0.95-inch RGB OLED with an SPI interface and a straight/vertical pin header.
* Operating voltage: 3.3 V or 5 V; driver chip is the SSD1331.
* Resolution 96 × 64 pixels, RGB color depth of approximately 65K colors.
* Module dimensions: 31.7 × 37 mm.
* Operating temperature: −20 °C to +70 °C; storage temperature: −30 °C to +80 °C.
* Viewing angle greater than 160°.
* Pinout: VCC (3.3 V/5 V), GND, NC, DIN (SPI data), CLK (SPI clock), CS (chip select, active-low), D/C (low = command, high = data), RES (reset, active-low).
* Only an SPI interface is present; although I²C is mentioned in the wiki, the module itself has SPI only.
* For Raspberry Pi: enable SPI via raspi-config and reboot; on Bookworm only the lgpio library is usable.
* Available C libraries: BCM2835, WiringPi, lgpio, plus a Python environment using spidev.

'''Commands and examples – verify before use:'''
<syntaxhighlight lang="text">
sudo raspi-config
sudo reboot
wget http://www.airspayce.com/mikem/bcm2835/bcm2835-1.71.tar.gz
tar zxvf bcm2835-1.71.tar.gz
cd bcm2835-1.71/
sudo ./configure && sudo make && sudo make check && sudo make install
sudo apt-get install wiringpi
wget https://project-downloads.drogon.net/wiringpi-latest.deb
sudo dpkg -i wiringpi-latest.deb
gpio -v
git clone https://github.com/WiringPi/WiringPi
cd WiringPi
./build
wget https://github.com/joan2937/lg/archive/master.zip
unzip master.zip
cd lg-master
sudo make install
sudo apt-get update
sudo apt-get install python3-pip
sudo apt-get install python3-pil
</syntaxhighlight>

== Notes and version constraints ==
* The source text contains unreliable template variables ({{{...}}); some sections are incomplete or polluted by navigation/marketing content.
* The exact current draw of about 38 mA at full white and about 4 mA at full black applies to the 0.95-inch RGB OLED at 3.3 V; other sizes have their own values.
* Displaying the same image for extended periods can cause afterimages and damage the OLED; periodic screen refresh recommended.
* Avoid reverse polarity on the power supply.
* Without program control the OLED will not light up because it has no backlight; software driving is required.
* Version-sensitive steps: On Bookworm, BCM2835 and WiringPi do not work – only lgpio is usable.
* On systems older than May 2019 the WiringPi upgrade step is omitted; from May 2019 onward a .deb update is required.
* Before running demos, ensure SPI is not occupied by other devices (check /boot/config.txt).
* Exact internal implementation details of the C libraries require inspecting DEV_Config.c/.h; switching between SPI/I²C must be done via macros there.
* Any claims about compatibility, certifications, warranty, or price are absent from the source and must not be added.

== Source and revision record ==
* [https://www.waveshare.com/wiki/0.95inch_RGB_OLED_(B) 0.95inch RGB OLED (B) - Waveshare Wiki]
* Source revision: 68703
* Captured: 2026-08-30T02:33:06+00:00
* SHA-256: <code>5dbc0c3c54a15a38cabe5081977609939f2a1576b11fac8baa1ff93a3bb909cc</code>

WSAL10514 – 0.95inch RGB OLED (B)/en - Versionsgeschichte

JWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex