https://wiki.jw-tech.eu/index.php?action=history&feed=atom&title=9085_%E2%80%93_0.96inch_OLED_%28A%29%2Fen9085 – 0.96inch OLED (A)/en - Versionsgeschichte2026-10-23T22:18:52ZVersionsgeschichte dieser Seite in JW Tech WikiMediaWiki 1.43.9https://wiki.jw-tech.eu/index.php?title=9085_%E2%80%93_0.96inch_OLED_(A)/en&diff=1332&oldid=prevJWTechPublisher: Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex2026-09-05T22:27:42Z<p>Freigegebene technische Dokumentation veröffentlicht; Text-only und noindex</p>
<p><b>Neue Seite</b></p><div>__NOINDEX__<br />
'''Documentation notice:''' This technical documentation was independently rewritten from an archived supplier source. Check technical details and commands against the product version and manufacturer documentation before use.<br />
<br />
== Summary ==<br />
Concise technical guide for the Waveshare 0.96inch OLED (A) module: specifications, pinout, interface selection (3-wire SPI, 4-wire SPI, I2C), and setup instructions for Raspberry Pi, STM32, and Arduino.<br />
<br />
== Related products at JW Tech ==<br />
* [https://shop.jw-tech.eu/p/9085 9085 – 0.96inch OLED (A)]<br />
* [https://shop.jw-tech.eu/p/WSAL9085 WSAL9085 – 0.96inch OLED (A)]<br />
<br />
== Technical overview ==<br />
* Operating voltage: 3.3 V or 5 V; default operation at 3.3 V.<br />
* Driver chip: SSD1306; resolution 128×64 pixels; display size 0.96 inch.<br />
* Interfaces: 3-wire SPI, 4-wire SPI, and I2C are selectable via two resistors (BS0/BS1) on the back of the module.<br />
* By default, 4-wire SPI communication is active (BS0=0, BS1=0).<br />
* For 3-wire SPI: connect BS0 to VCC and BS1 to GND.<br />
* For I2C: connect BS0 to GND and BS1 to VCC; the DC pin sets the I2C address (GND → address 0x3C).<br />
* Pinout: VCC, GND, DIN (SPI data input), CLK (SPI clock input), CS (chip select, low active), D/C (command/data signal), RES (reset, low active).<br />
* Operating temperature: −20 °C to 70 °C; storage temperature: −30 °C to 80 °C; viewing angle &gt;160°.<br />
* When connecting to a Raspberry Pi, use a 7-pin cable; pin mapping: DIN→MOSI/SDA (BCM19/3), CLK→SCLK/SCL (BCM23/5), CS→CE0 (BCM24), DC→BCM25 (pin 22), RES→BCM27 (pin 13).<br />
<br />
'''Commands and examples – verify before use:''' <br />
<syntaxhighlight lang="text"><br />
sudo raspi-config<br />
sudo reboot<br />
sudo ./main 0.96<br />
sudo python3 OLED_0in96_test.py<br />
</syntaxhighlight><br />
<br />
== Notes and version constraints ==<br />
* The exact resistor wiring for interface selection must be verified physically on the module; the source only specifies logical states (0/1).<br />
* When using I2C, the slave address depends on the DC pin; incorrect wiring may cause communication errors.<br />
* The source contains placeholders (&#123;&#123;&#123;...&#125;&#125;), indicating incomplete documentation; certain values may be missing or outdated.<br />
* Compatibility with specific Raspberry Pi OS versions (e.g., Bookworm) is limited: only lgpio is available; BCM2835 and WiringPi cannot be installed.<br />
* Before operation, ensure the correct interface is selected via hardware configuration; otherwise communication may fail.<br />
<br />
== Source and revision record ==<br />
* [https://www.waveshare.com/wiki/0.96inch_OLED_(A) 0.96inch OLED (A) - Waveshare Wiki]<br />
* Source revision: 69961<br />
* Captured: 2026-08-29T09:23:12+00:00<br />
* SHA-256: <code>eeb628e9d72ac2e24e796d9014909f3bf51aca8ab61297ccc0c925bbf06ce740</code></div>JWTechPublisher